Sunday, January 15, 2012

Kick Pleat Valances

Kick Pleat valances are a great way to top any window.  They've got crisp clean lines that can be played down with a simple solid fabric or spiced up with a bright colored patterned fabric.  Custom details can also be added to give them character.  Here's a few I've made for clients in the past.

This is an example of a basic, clean line kick pleat valance.  The pattern of the fabric almost acts like a solid and tops these basic drapery panels to give them a finished look.




Now here's an example of how fabric and contrast banding can make these anything but boring! 

Then there's this one that is completely customized with a scallop in the middle and a fan fold ruffle adorning the bottom and top edges. 

Here's the one I'm featuring in todays tutorial.
Isn't she adorable!  The fabric alone gives it a lot of interest, but then Mother of Pearl buttons were added to the top of each kick pleat to add a little whimsy.

There's a few things to consider when making a kick pleat valance.  After measuring the width of your window you must decide on the sections.  Odd number is always best.  You also have to decide on the length of the valance.  You may not want it to obstruct your view out the window, in which case it can be hung several inches above the window.  Once you have figured out the number of sections you want, you have to decide on fabric and motifs.  This ones motif did not fit within the space of the sections however, the pattern worked regardless.  If you choose a large patterned fabric to use on a small valance, just keep in mind what part and how much of the motif is actually going to show. 

Since there's so much going on behind the scenes of a kick pleat valance and we don't want there to be shading when sunlight shines through, we always use blackout lining on these.  In fact as a rule most valance styles are always lined with black out lining.  The good thing is kick pleat valances require minimal amounts of lining.

The finished size of this valance is 26" wide x 13" long.  We decided to have 3 sections and 4 pleats and it will be mounted on a 1x2 (which nets a size of 1 1/2")

What you'll need:  Fabric, blackout lining, thread, board and buttons.

Lets do the math to figure the length of our cuts.
I always make sure the face fabric wraps around the bottom towards the back of the valance by 2", so our cuts will include that.
1 1/2"(depth of board)+13"(finished length of valance)+2"(towards the back)+ 1/2"(seam allowance)=17" (length of each cut)

If you've never worked with blackout lining, it has a rubber-like coating that blocks out all light.  That rubberized coating also makes it kind of thick and it doesn't crease very well when pressed.  It also doesn't unravel or Frey like regular fabrics do.  Because of these factors, I construct things a little differently when I'm using blackout lining. 

To figure the length of the blackout lining cuts, here's the math.
1 1/2"(board depth)+ 13"(finished length of valance)=14 1/2" 
There's no seam allowance added into the blackout lining math because of the way I construct this valance.  The lining gets butted up against the inside of the hem fold line of the face fabric.  I'll try to explain in this illustration.
Now that we have the length of our cuts determined, we have to figure the width of each cut.  The width of the cuts will be completely determined by the number of sections in the valance and the fabric used for the valance.
My valance has 3 sections with 2 kick pleats separating the 3 sections and 2 half kick pleats at the ends of the board.  Take the finished width of your valance (26) divided by number of sections(3)= width of sections.  Since mine came out uneven, my sections will be 8 3/4, 8 1/2, 8 3/4.  The 1/4" difference will never be noticeable.
Our kick pleats are going to be 3" deep.  You can make them as small as 2" if necessary, but I wouldn't go any smaller than that because you need that fullness in there for the valance to lay smoothly.

If you've chosen a solid fabric for your valance your cut widths will be much easier to figure.  If you've chosen a patterned fabric then you will have to figure your cuts around centering your motif in the center of each section.

Lets look at the workings of the valance first to help you understand what factors come into play.
More than likely you will have to use more than one cut of fabric for this valance.  You will definitely have more than one cut if you are using a fabric with a large motif to be centered in the middle of each section.  So lets look at where the seams are to be placed.
My Motifs landed on the fabric in such a way that I had to cut a piece for each section.  My cut for the first section on the left side of the valance was 26 1/4" wide x 17" long.  Here's how I got my cut size.
1/2"(seam allow)+1 1/2"(return for board depth)+3"+3"(half a kick pleat)+8 3/4"(left front section)+3"+3"+3"(3/4 of my kick pleat at which point I need to make a seam)+1/2"(seam allow)=26 1/4".  Here's visual if you are having a hard time understanding the cut.  It also shows where your motif should be centered.  Please excuse my drawing, I'm not very good at Microsoft Paint yet and there is a lot to explain in this drawing.  I tried to make it as simple as possible, but as I said, there is a lot to explain in this one drawing.  You may need to take a few minutes to study the drawing to understand the full concept.  Once you have the "ah ha" moment, you will "get" it and it will make understanding the rest of the cuts much easier.

Whew!  That was a lot of information at once.  I usually draw all my cuts out on the fabric before I begin to cut just in case there needs to be any adjustments because of fabric shortage.  Now lets figure our 2nd cut, the center cut.

 Notice that my first cut was positioned on the right hand area of my fabric and the middle section is positioned in the middle area of my fabric.  This is where my motifs happened to land on my fabric.  The third cut had to be cut out of the same motif as section one except that motif was too close to the selvage edge of the fabric to be cut there.  Thank goodness that same motif was also positioned on the left side of my fabric.  Keep these kinds of things in mind when planning your valance.

You may have more then 3 sections in your valance, in other words you might have several center sections.  They will probably end up being the same width as the one we figured as our middle section, so you will just repeat that cut as many times as necessary to get all your sections cut.  I usually number mine starting from the left side of the valance so I don't confuse them when it's time to sew them together.  You don't want to accidentally sew them out of order.

You have officially finished the hardest part of this valance!  Give yourself a pat on the back if you are still with me here!
Now we need to cut our Blackout lining.  Here's how we figure the length to cut our Blackout lining.  13"(finished length of valance)+1 1/2"(board allowance)=14 1/2"
Our widths are going to be the same as our face fabric except in reverse order.  So I cut 3 pieces.  The first one 26 1/4" wide, the second one 21 1/2" wide and the third one 20 1/4".  The difference is I numbered them from right to left this time.  This ensures our seams will be in those kick pleats and that the Blackout lining seams will not land in the same place as the seams for our face fabric.  If they all landed in the same place, this would cause a lot of bulk, we want to spread out our bulk.

Finally we can get to the sewing part of this tutorial.  Stitch your face pieces together in the order they are numbered starting from the left side.  Stitch your Blackout lining pieces together in the order they are numbered starting from the right side.
Press all these seams open.  Try to get the Blackout lining seams as flat as possible.
With the right side of your Blackout lining facing up, draw a line along the bottom edge 1 1/2" from the bottom.  Use a pencil to do this.
With right sides together, pin the bottom edge of your valance to this line.
Stitch along this bottom edge 1/2" from the raw edge of the valance face.
Open the two pieces up and lay them face down on your pressing area and press the Blackout bottom edge towards the fabric.
With it laying just like it shown in the picture above, bring the top of the face fabric up to meet the top of the Blackout lining.

Press this bottom edge really well, this is the bottom edge of your valance.  Put pins along the top edge of the valance starting about 12" in from the sides.  Place the pins parallel with the top edge about 1" from the top edge.

Now we have to sew the side seams.  We need to fold the right sides together along the sides folding it over itself where we made that pressed crease.  It might be hard to get this to lay flat for sewing, so if you need to take a few pins out of the top to get it to lay flat, then do so.
Here's another picture of that step.  Pin both side edges.
Stitch along the sides using 1/2" seam allowance.
Clip the bottom corners as shown below.

Now turn those corners right side out again and give them a good pressing.  Re pin the top 1" from the top with pins parallel.  Serge this top edge or zig zag along the top edge to keep the layers together and to finish off that top edge.  It's OK if the 2 layers are not lined up exactly with each other.  Just serge along the outer of the 2 layers.

Our sewing is now complete!  Minimal sewing huh?! :-)
Now we need to cut our board.  I used a 1x2 which nets an actual size of 1 1/2"x3/4".  I get mine at my local Hardware store.  They don't have to be anything fancy because they are going to be covered with fabric.  But you DO want to try to get one that is as straight as possible.  Notice the really warped one in the right hand side of this picture.  Something like that would make our valance hang uneven.

My finished valance width is 26" so I cit my board to 26".

Cut a piece of scrap fabric.  I'm using a piece of regular white lining.  I don't recommend using the Blackout lining for this because it is so thick that it will add too much bulk.  Use a piece of your face fabric if necessary.  Cut your scrap piece 4" longer than your board and 5 1/2" wide.  Lay your board in the center of this scrap and pull one long edge up and over the board and staple all along the long edge approx. every 4" or so.
Now pull the other long edge up and over that and staple in the same manner.

Trim the excess lining from the fabric that is extending past your board like this.

Push the sides in slightly with your fingers and wrap this fabric up over your board and staple.  Trim off excess after stapling.

Before we can mount the valance to the board we must do 2 things: 1. draw our lines where the pleats will land.  2.  Pin in our pleats.

First draw a line with a pencil 1 1/2" in from each side of the board.  Now measure over from the edge of the board and draw a line where your first pleat will land.  In my case my first section is 8 3/4", so my line is drawn 8 3/4" from the side of the board.  My second section is 8 1/2" wide, so I drew a line 8 1/2" from the first sections line.  The remaining area should equal 8 3/4" for my third section.

Using a hem gauge, I pin in the pleats at the top of the valance.  Once I have them all pinned in correctly, I give the pleats a good pressing with my iron.  With your hem gauge, measure over 1 1/2" from each side and place a pin there to mark it.  Then form 3" deep half pleat.
Measure over from there the width of your section (in my case 8 3/4") and form a complete 3" pleat.  Pin.  Continue until you have all your pleats pinned in.  Lay your board above your valance and you should see the pleats lining up with the lines on your board.  There should also be 1 1/2" extending beyond each side of your board.  This is the return.  Wrap the return around to the sides of your board and staple them to the pencil line that is 1 1/2" from the edge.  Staple them diagonally like shown in this picture.

Pivot the rest of your valance to the front edge and bring it to the top of the board, it will stack on top of the return we already stapled to the board.
Staple at every edge of a pleat and 3-4" apart every where else.  Pull the pins out after you staple.  If you decided to add buttons to the top of your valance, this is when you would add them. 
Tada!!!  Your valance is done! :-)  Use a couple "L" brackets to hang it above your window.  Hang the "L" brackets first, then set your valance on top of the "L" brackets and screw from underside through the holes in the bracket right into the wood.  Step back and take a look at your finished valance.  Give yourself a HUGE pat on the back because I know these directions got a little complicated at times and you stuck with me and finished the valance.
As I said at the beginning of this tutorial, all kinds of Custom details can be added to Kick Pleat valances.  I'll do some tutorials on those another day....so follow me and stay tuned! Pin It

25 comments:

  1. Hi there! Great tutorial! Thanks for dropping by my place earlier! I'm gonna post some more tips on the way, so stay tuned! Meanwhile, a little bit of observation if I may... how can someone follow you? I think you should add the followers gadget somewhere on the top so that people can follow you when they visit your lovely blog!
    Can't wait to see how your blog grows!
    Love, Olga
    www.stardust-decorstyle.blogspot.com

    ReplyDelete
    Replies
    1. Hi Olga, I'll look forward to your future tips! Thanks for the advice...as you can see I'm a sewer and I'm not very good with computers. I thought I had the followers gadget on my blog, but now that I look, it's not there. I must have done something wrong when installing it. Sometimes it takes me hours to figure out to do the simplest thing on my blog, but I'm learning.
      I'll try to figure it out in the morning. Thanks for pointing it out and thanks for the encouragement! Thanks again, Jules

      Delete
  2. This is a great tutorial!! TFS!! I am stopping by from The Blackberry Vine linky party and I'm your newest follower here and on Pinterest.

    Here is what I shared this week: http://craftybrooklynarmywife.blogspot.com/2012/01/hollys-first-coat.html

    ReplyDelete
    Replies
    1. Hi Alisha, Glad you liked mt tutorial and thanks for following! I'll hop over in the morning and follow you.
      So you're an Army wife? I live in Fallbrook which is located right outside the back gate to Camp Pendleton Marine Base. I have several Marine Wife friends and I see first hand how much you ladies sacrifice, you have my thanks and respect!
      Jules

      Delete
  3. This comment has been removed by the author.

    ReplyDelete
  4. This comment has been removed by the author.

    ReplyDelete
  5. This is the best tutorial! Your directions are very easy to follow. I'm half way through my first valance and had to stop and send you a thank you. We're on a temporary assignment care of the military in an (awful) rental and I think some valances are going to make a world of difference.

    ReplyDelete
    Replies
    1. Hi Karin,
      Oh I'm so relieved to hear that!! I've been so worried that I'm not making sense when I'm trying to explain this stuff.
      I'm so happy to hear you are making valances from my tutorial!! I'd love to see pics when you're done!!
      Where is your family stationed at right now? I live in Fallbrook which is right outside the back gate of Camp Pendleton Marine base. I have many friends who are military wives. You ladies have my complete respect and thanks.
      Jules

      Delete
  6. Okay - this looks totally do-able! I am itching to do some updating to our living room. I am next to inept when it comes to interior design, but I love the clean lines here, and by making my own, I could use any fabric I like. Hmmm.... :)

    Thanks for dropping by Happy Hour Projects, following you!

    Adrianne
    www.happyhourprojects.com

    ReplyDelete
    Replies
    1. Hi Adrianne,
      It is do-able. I promise if you can sew a straight line, you can make this valance. And yes, thats the another bonus of making things yourself, you can use any fabric your heart desires! Let me know if you make one...I'd love to see pictures!
      Jules

      Delete
  7. You make it look so easy! I love your fabric.

    ReplyDelete
    Replies
    1. Hi Marla and Steve, It is easy...I promise it is! I just stopped by your blog, I'm now following you. How neat you guys are partners in the blogging. I bet you guys make a great team and I look forward to seeing your stuff.
      Jules

      Delete
  8. What a marvelous tutorial!! Thanks for sharing! Your gorgeous valance will be featured later this evening on the Tuesday To Do Party!
    Smiles!
    Jami

    ReplyDelete
    Replies
    1. Hi Jami,
      Thank you so much, I'm honored that you would feature my valance!!!!
      Jules

      Delete
  9. Hi Jami, Sooo glad you liked the valance tutorial! And I'm feel so honored to be featured on your blogs Tuesday To Do List!!
    Thank you so much!!
    Jules

    ReplyDelete
  10. I just stumbled upon this tutotial - thanks so much! There is one thing I can't figure out... Why do you add the depth of the board (1.5") to the length of the fabric cut?

    ReplyDelete
  11. Write more, thats all I have to say. Literally, it seems as though you relied on the video to make your point.
    You obviously know what youre talking about, why waste your intelligence on just posting videos to your blog when you could be giving us something enlightening to read?


    Also visit my website - como alargar pene

    ReplyDelete
  12. Its like you read my mind! You seem to know a
    lot about this, like you wrote the book in it or something.
    I think that you could do with some pics to drive the message
    home a little bit, but instead of that, this is magnificent blog.

    A great read. I will certainly be back.

    Visit my web blog; penis gigante

    ReplyDelete
  13. First off I would like to say wonderful blog! I had a quick question in
    which I'd like to ask if you do not mind. I was curious to know how you center yourself and clear your mind prior to writing. I have had a tough time clearing my mind in getting my ideas out there. I truly do enjoy writing but it just seems like the first 10 to 15 minutes are usually wasted just trying to figure out how to begin. Any suggestions or hints? Thanks!

    Review my weblog agrandar el pene

    ReplyDelete
  14. This tutorial is AMAZING!!! So easy and great pictures to demonstrate!! Appreciate you sharing!! <3 <3

    ReplyDelete
  15. pop over to this web-site luxury replica bags additional resources Ysl replica bags dig this gucci replica handbags

    ReplyDelete